Product ID:GENERAL PURPOSE ALUMINUM PAINT, 6-230
MSDS Date:10/24/1995
FSC:8010
NIIN:00N026182
Status Code:A
MSDS Number: CJFQW

PPG INDUSTRIES INC

4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 304-843-1300

Info Phone: 304-843-1300;800-441-9695

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

ALUMINUM; (ALUMINUM POWDER)

CAS: 7429-90-5

RTECS: BD0330000

OSHA PEL 15 MG/M3 RDUST (TWA)

ACGIH TLV: 10 MG/M3 (TWA)

SOLVENT NAPHTHA (PETROLEUM), MEDIUM ALIPHATIC; (NAPHTHA)

CAS: 64742-88-7

LIGHT AROMATIC SOLVENT NAPHTHA (PETROLEUM); (AROMATIC

CAS: 64742-95-6

RTECS: WF3400000

NAPHTHA, SOLVENT; (NAPHTHA)

CAS: 8052-41-3

RTECS: WJ8925000

OSHA PEL 2900 MG/M3;500 PPM

ACGIH TLV: 525 MG/M3;100 PPM

HYDROCARBON PETROLEUM RESIN

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGESTION: HARMFUL IF
SWALLOWED. EYE CONTACT: CAUSES IRRITATION. SKIN CONTACT: MAY CAUSE
MODERATE IRRITATION. MAY BE ABSORBED THROUGH SKIN. INHALATION:
VAPOR &/ SPRAY MIST MAY BE HARMFUL IF INH ALED. REPEATED EXPOSURE
TO HIGH VAPOR CONCENTRATIONS MAY CAUSE IRRITATION OF THE
RESPIRATORY SYSTEM & PERMANENT BRAIN & NERVOUS SYSTEM DAMAGE.
CHRONIC: AVOID LONG-TERM & REPEATED CONTACT.
Effects of Overexposure:EYE WATERING, HEADACHES, NAUSEA, DIZZINESS &
LOSS OF COORDINATION ARE INDICATIONS THAT SOLVENT LEVELS ARE TOO
HIGH. INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING & INHALING
CONTENTS CAN BE HARMFUL OR FATAL. REDNESS, ITCHING, BURNING
SENSATION & VISUAL DISTURBANCES MAY INDICATE EXCESSIVE EYE CONTACT.
DRYNESS, ITCHING, CRACKING, BURNING, REDNESS & SWELLING ARE
CONDITIONS ASSOCIATED WITH EXCESSIV E SKIN CONTACT.
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid:INGEST: DO NOT INDUCE VOMITING. GENTLY WIPE OUT INSIDE MOUTH
TO REMOVE ANY RESIDUAL MATERIAL. EYES: REMOVE CONTACT LENSES &
FLUSH IMMEDIATELY W/GENTLE STREAM OF LUKE WARM WATER FOR AT LEAST
15 MINUT ES. SKIN: FLUSH IMMEDIATELY W/PLENTY OF WATER FOR AT LEAST
15 MINUTES FOLLOWED BY WASHING W/SOAP & WATER. INHAL: REMOVE TO
FRESH AIR. APPLY ARTF RESP & OTHER SUPPORTIVE MEASURES AS REQUIRED.
-- IF ING ESTION, ANY TYPE OF OVEREXPOSURE OR SYMPTOMS OF
OVEREXPOSURE OCCUR DURING OR FOLLOWING USE OF THIS PRODUCT, CONTACT
POIS CTL CTR, EMERGENCY ROOM OR MD IMMEDIATELY; HAVE MSDS INFO
AVAILABLE.

Flash Point Method:PMCC
Flash Point:=30.6C, 87.F
Lower Limits:1.0%
Extinguishing Media:USE NFPA CLASS B EXTINGUISHERS (CARBON DIOXIDE, DRY
CHEMICAL OR UNIVERSAL AQUEOUS FILM FORMING FOAM) DESIGNED TO
EXTINGUISH NFPA CLASS IC FLAMMABLE LIQUID FIRES.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . WATER SPRAY MAY BE INEFFECTIVE. WATER SPRAY MAY BE USED
TO COOL CLOSED CONTAINERS TO PREVENT PRESSURE BUILD-UP & POSSIBLE
AUTOIGNITION OR EX PLOSION WHEN EXPOSED TO EXTREME HEAT. IF WATER
IS USED, FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:WHEN THIS PROD IS USED, OVERSPRAY & OTHER
COMBUST MATLS SUCH AS PAINT BOOTH FILTERS, RAGS, MASKING MATLS,
ETC, CONTAM BY COATING MATL ARE SUBJECT TO SPONT COMBUST. WETTING
CONTAM MATLS & NOT PACKING T HEM TIGHTLY TOGETHER IN REFUSE CNTNRS
WILL MIN POTNTL FOR THIS TO OCCUR. KEEP PROD FROM HEAT, SPKS, (SUPP
DATA)

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ONLY PERSONNEL
EQUIPPED W/PROPER NIOSH APPROVED RESPIRATORY, SKIN & EYE PROTECTION
SHOULD BE PERMITTED IN AREA. REMOVE ALL SOURCES OF IGNITION. TAKE
UP SPILLED MATERIAL W/ SAND, VERMICULITE OR OTHER NONCOMBUSTIBLE
ABSORBENT MATERIAL & PLACE IN CLEAN, EMPTY CONTAINERS FOR
DISPOSAL. ONLY SPILLED MATERIAL & ABSORBANT SHOULD BE PLACED IN
THIS CONTAINER.

Handling and Storage Precautions:DO NOT STORE >120F (48C). STORE LG
QTYS IN BLDGS DESIGNED & PROTECTED FOR STORAGE OF NFPA CLASS IC
FLAMM LIQS. FLAMM. KEEP AWAY FROM HEAT, SPARKS, FLAMES & OTHER
SOURCES OF IGNIT. DO NOT SMOKE. EXTING ALL FLAMES & PILOT LIGHTS.
TURN OFF STOVES, HEATERS, ELEC MOTORS & OTHER SOURCES OF(SUPP
DATA)
Other Precautions:VAPORS MAY COLLECT IN LOW AREAS. IF THIS MATERIAL IS
PART OF A MULTIPLE COMPONENT SYSTEM, READ MSDS(S) FOR OTHER
COMPONENTS BEFORE BLENDING AS RESULTING MIXTURE MAY HAVE HAZARDS OF
ALL OF ITS PARTS. C ONTAINERS SHOULD BE GROUNDED WHEN POURING.
AVOID FREE FALL OF LIQUIDS IN EXCESS OF A FEW INCHES.

Respiratory Protection:OVEREXP TO VAPS MAY BE PREVENTED BY ENSURING
PROPER VENT CONTROLS, VAP EXHST OR FRESH AIR ENTRY. A NIOSH APPRVD
AIR PURIFYING RESP W/APPROP CHEM CARTRIDGES OR POS-PRESS,
AIR-SUPPLIED RESP MAY ALSO RED UCE EXPOS. READ RESP MFR'S
INSTRUCTIONS & LITERATURE CAREFULLY TO DETERMINE TYPE OF AIRBORNE
CONTAMS AGAINST WHICH RESP IS EFTIVE, ITS (OTHER INFO)
Ventilation:PROVIDE GEN DILUTION/LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF INGS BELOW LOWEST SUGGESTED EXPOS LIMS, LEL BELOW
STATED LIM & TO REMOVE (OTHER INFO)
Protective Gloves:NEOPRENE RUBBER OR NITRILE RUBBER GLOVES.
Eye Protection:ANSI APPROVED CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
WEAR PROT CLTHG TO PREVENT SKIN CONT. APRON SHOULD BE CONSTRUCTED
OF: NEOPRENE RUBBER OR NITRILE RUBBER. NO SPECIFIC
PERMEATION/DEGRADATION(OTHER INFO)
Work Hygienic Practices:CLEAN CONTAMINATED CLOTHING OR SHOES.
Supplemental Safety and Health
HNDLG/STOR PREC: IGNIT DURING USE & UNTIL ALL VAPS/ODORS ARE GONE. SAFE
HNDLG OF THIS PROD REQS THAT ALL OF INFO ON MSDS BE EVALUATED FOR
SPECIFIC WORK ENIVIRONS & CNDTNS OF USE. EXPLO HAZ: FLAME & O THER
SOURCES OF IGNIT (I.E., PILOT LIGHTS, ELEC MOTORS, STATIC ELEC). I
NVISIBLE VAPS CAN TRAVEL TO (OTHER INFO)

Boiling Pt:>154.4C, 310.F
B.P. Text:310-4000F
Vapor Pres:1.5 MMHG
Vapor Density:HVR/AIR
Spec Gravity:0.916
Evaporation Rate & Reference:16 (BUOAC=100)
Solubility in Water:0.0%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
SOLVENTS LISTED IN INGS.
Percent Volatiles by Volume:63.560

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:THIS PRODUCT IS NORMALLY STABLE BUT MAY
UNDERGO HAZARDOUS REACTIONS AT EXTREMELY HIGH TEMPERATURES &
PRESSURES.
Hazardous Decomposition Products:MAY PRDCE FOLLOWING HAZ DECOMP PRODS
WHEN EXPOS TO EXTREME HEAT: CARBON MONOXIDE, CARBON DIOXIDE, OXIDES
OF ALUMINUM, LOWER MOLECULAR WT POLYMER FRACTIONS. EXTREME HEAT
INCLS, BUT IS (TOX INFO)

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF I/A/W
FEDERAL, STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MANAGEMEN T FACILITY.

Toxicological Information:HAZ DECOMP PROD:NOT LIMITED TO, FLAME
CUTTING, BRAZING & WELDING.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.

SARA Title III Information:THIS MSDS HAS BEEN PREPARED I/A/W THE
SUPPLIER NOTIFICATION REQUIREMENTS OF SARA TITLE III, SECTION 313 &
OTHER APPLICABLE RIGHT-TO-KNOW REGULATIONS.
Federal Regulatory Information:PRODUCT STATUS RELATIVE TO THE U.S. EPA
TOXIC SUBSTANCES CONTROL ACT - ALL CHEMICAL SUBSTANCES IN THIS
PRODUCT ARE LISTED ON THE U.S. TSCA INVENTORY OR ARE OTHERWISE
EXEMPT FROM TSCA INVENTORY REPORTI NG REQUIREMENTS. THIS MSDS HAS
BEEN PREPARED I/A/W THE OSHA HAZARD COMMUNICATION STANDARD (29 CFR
1910.1200).